Or Call us at: (888) 388-6514
How to Put a Track Back on a Mini Excavator — Guide
Knowing how to put a track back on a mini excavator saves hours of downtime and eliminates the cost of a service call. The process takes 20 to 45 minutes with basic hand tools — a pry bar, a grease gun, and the machine's own hydraulics do most of the work. Release track tension through the grease valve, position the track over the sprocket, use the drive motor to walk it into place, then re-tension to the correct sag. One person can handle it in the field with the right technique.
Why Does a Mini Excavator Track Come Off?
Debris buildup, improper tension, and worn undercarriage components cause most track derailments on mini excavators. Identifying the root cause before reinstalling the track prevents repeat failures on the same jobsite.
What Causes Track Derailment on Mini Excavators?
Mud, rocks, and packed soil between the rollers and sprocket are the most frequent cause of a thrown track. Material wedged into the undercarriage pushes the track out of alignment. Excessive track sag from low tension compounds the problem.
- Packed debris between the sprocket teeth and track lugs
- Track tension set too loose — sag exceeding 1.5 inches at midpoint
- Rapid pivot turns or counter-rotation that stress track alignment
How Does Worn Undercarriage Hardware Lead to Thrown Tracks?
Worn rollers, idlers, and sprocket teeth allow the track to move laterally under load. A roller with flat spots or a sprocket missing tooth profile no longer guides the track along the correct path. Inspect all undercarriage hardware after any derailment.
Can Operating on Slopes or Uneven Ground Throw a Track?
Side-hill operation places uneven lateral force on the track, increasing derailment risk. Working across a slope greater than 15 degrees pushes the track toward the downhill side. Tight pivot turns on uneven terrain multiply this lateral force and accelerate wear on guide lugs.
Shop Earthmoving Digging Attachments for This Job
These 10 picks from our earthmoving digging attachments range cover the equipment this job calls for. Check each product's specs against your machine and job before ordering. Browse all earthmoving digging attachments.
Auger Bit for Power Augers | 10" x 36" | 7/8" Square Drive | Earth Drilling | Brave$469
8" x 36" Auger Bit for Skid Steer | Carbide Tip | Heat-Treated Steel | Brave$446
Auger Bit for Skid Steer | Commercial Drilling | 14 Inch Diameter | Brave$605
4" x 36" Auger Bit for Standard Drives | Heat-Treated Edges | Brave$391
Brave Pro 5-In. Bedmaster Rotor Trencher for Walk-Behind | 9-Inch Depth | Honda GX270 | Brave$4,990
Bit Extension Auger for Earth Auger | 15" Length | 1.38" Hex Drive | Brave$152
Bucket for Mini Skid Steer | 3/16" Steel | 3/8" Cutting Blade | Star Industries$928
Push Drop Spreader | Walk Behind Style | 50-Lb Capacity | 13-In Wheels | Stainless Steel | Spyker$624
Compact Tractor Rock Bucket Attachment – Sifting Rocks and Debris with Ease | Stinger Attachments$1,095
Compact Tractor Rock Grapple Attachment – Built for Land Clearing and Debris Handling | Stinger Attachments$2,495
What Tools and Equipment Do You Need to Put a Track Back on a Mini Excavator?
Reinstalling a thrown track requires 4 items: a pry bar, a grease gun, a wrench set, and the machine's own boom and bucket for lifting. Each tool addresses a specific step in the reinstallation sequence.
What Hand Tools Are Required for Track Reinstallation?
A 36-inch pry bar, a grease gun with a standard coupler, and a wrench or socket set matching the track adjuster valve are the minimum hand tools. The pry bar provides leverage to guide the track over the sprocket teeth and front idler.
- 36-inch pry bar — for prying the track onto the sprocket
- Grease gun — for releasing and re-applying track tension
- Wrench or socket set (typically 19 mm or 3/4 inch) — for the track adjuster relief valve
- Wire brush or flat-blade scraper — for clearing packed debris
Do You Need a Jack or Lifting Equipment?
No separate jack or lift is required. Use the excavator's own boom and bucket to raise the derailed side off the ground. Curl the bucket flat, extend the boom to the side with the thrown track, and press down until the track clears the ground by 2 to 3 inches.
How Do You Put a Track Back on a Mini Excavator Step by Step?
Reinstalling a thrown track follows 6 steps over 20 to 45 minutes depending on debris accumulation and track condition. Each step has a visible completion point before moving to the next.
What Are the Steps to Reinstall a Mini Excavator Track?
The 6 steps below cover lifting, tension release, debris removal, positioning, seating, and re-tensioning.
- Lift the derailed side. Position the boom perpendicular to the derailed track. Curl the bucket flat against the ground and press down until the track side lifts 2 to 3 inches off the surface. Keep the opposite track grounded for stability.
- Release track tension. Locate the track adjuster grease valve on the front idler assembly. Loosen the relief valve slowly — 1/4 turn at a time — using the correct wrench. Grease exits under extreme pressure; stand to the side and wear eye protection. Allow grease to bleed until the front idler retracts and the track hangs slack.
- Clear all debris. Remove packed mud, rocks, and soil from the sprocket teeth, rollers, idler, and track lugs using a wire brush or scraper. Debris left in the undercarriage causes immediate re-derailment.
- Position the track over the sprocket. Drape the track over the rear drive sprocket first. Use the pry bar to lever the track onto the sprocket teeth, working from the bottom up. Ensure the track lugs engage the sprocket tooth pattern fully.
- Walk the track onto the idler. Start the engine and briefly pulse the drive motor in forward to rotate the sprocket. The sprocket pulls the track around the rollers and onto the front idler. Use the pry bar to guide the track over the idler as the sprocket rotates. Stop the engine once the track seats around the full undercarriage.
- Re-tension the track. Pump grease into the track adjuster valve using the grease gun. Continue pumping until the track sag at the midpoint between the front idler and rear sprocket measures 1 to 1.5 inches. Check the sag by pressing down on the track at the midpoint and measuring deflection.
What Are the Most Common Mistakes During Track Reinstallation?
Skipping debris removal is the most common mistake. Operators reinstall the track over packed material, and the track derails again within minutes. Taking 5 to 10 minutes to fully clean the undercarriage before reinstalling eliminates this cycle.
- Skipping debris removal — causes immediate re-derailment — clear all material before positioning the track
- Releasing the grease valve too fast — high-pressure grease ejects dangerously — turn the valve 1/4 turn at a time
- Over-tensioning the track — accelerates wear on rollers and sprocket — maintain 1 to 1.5 inches of sag at midpoint
What Safety Precautions Apply When Putting a Track Back on a Mini Excavator?
Track reinstallation safety requires 3 controls: PPE for high-pressure grease hazards, stable machine positioning, and engine lockout during manual work near the undercarriage. Each control prevents a specific crushing or injection injury.
What Personal Protective Equipment Is Needed?
Safety glasses, heavy-duty gloves, and steel-toed boots are the minimum PPE for track work. The track adjuster valve releases grease at pressures exceeding 3,000 PSI. A high-pressure grease stream penetrates skin and causes injection injuries requiring emergency surgery. Stand to the side of the valve — never position any body part in front of the grease port.
How Do You Safely Lift and Support the Machine?
Use the boom and bucket on firm, level ground only. Place the bucket on compacted soil or a wood block to prevent sinking. Shut off the engine and remove the key before placing hands or tools near the sprocket, rollers, or track. Engage the drive motor only from the operator's seat with all personnel clear of the undercarriage.
How Do You Prevent a Mini Excavator Track From Coming Off Again?
Preventing repeat derailments involves 3 ongoing practices: regular tension checks, undercarriage cleaning, and timely replacement of worn rollers, idlers, and sprockets. Skipping any practice shortens undercarriage life and increases derailment frequency.
How Often Should You Check Track Tension?
Check track tension every 8 to 10 operating hours. In muddy or rocky conditions, check tension at the start of every shift. Correct sag measures 1 to 1.5 inches at the midpoint between the front idler and rear sprocket. Over-tight tracks accelerate roller and idler bearing wear. Loose tracks ride off the sprocket during turns.
What Undercarriage Maintenance Keeps Tracks Seated?
Clean packed debris from the undercarriage at the end of every work day. Use a pressure washer or hand tools to remove mud and rocks from between the rollers, idler, and sprocket teeth. Operating the machine in tight circles or repeated pivot turns wears guide lugs and track edges — minimize counter-rotation whenever possible.
When Should You Replace Worn Rollers, Idlers, or Sprockets?
Replace rollers showing flat spots, idlers with excessive play, or sprockets with worn or missing tooth profiles. Visible metal shavings around the undercarriage indicate component wear past service limits. A sprocket with rounded teeth no longer engages the track lugs and causes slippage under load, leading to derailment.
Frequently Asked Questions About Putting a Track Back on a Mini Excavator
The most common track reinstallation questions cover crew requirements, time estimates, undercarriage damage, track replacement, and correct tension specifications. The answers below resolve each with specific numbers and field-tested guidance.
Can One Person Put a Mini Excavator Track Back On Alone?
One person can reinstall a thrown mini excavator track without assistance in 20 to 45 minutes.
The machine's boom and bucket handle the lifting. The drive motor rotates the sprocket to walk the track into position. The only manual effort involves using a pry bar to guide the track over the sprocket teeth and idler. A second person speeds the process but is not required for machines under 10,000 pounds operating weight.
How Long Does It Take to Reinstall a Thrown Track?
A clean reinstallation with minimal debris takes 20 minutes. Heavy mud or rock packing extends the job to 45 minutes.
Most of the time goes to debris removal and tension adjustment rather than physical track positioning. Having a grease gun, pry bar, and correct wrench staged before starting eliminates trips back to the truck. Operators who have reinstalled a track once typically complete subsequent reinstallations in under 25 minutes.
Does a Thrown Track Damage the Undercarriage?
A single derailment rarely causes permanent damage if the operator stops the machine immediately.
Continuing to operate with a thrown track grinds the track against the frame, wears roller flanges, and bends the idler bracket. Inspect the rollers, sprocket teeth, and idler for scoring or deformation after every derailment. Repeated derailments on the same side indicate worn components that require replacement rather than repeated reinstallation.
Should You Replace a Track That Keeps Coming Off?
Tracks that derail repeatedly despite correct tension and clean undercarriage components have stretched beyond service limits and require replacement.
A stretched track no longer maintains proper engagement with the sprocket teeth even at maximum adjuster extension. Measure the track tension with the adjuster fully extended — if sag still exceeds 1.5 inches, the track is stretched. Worn guide lugs on the inside of the track also contribute to chronic derailment on otherwise serviceable undercarriages.
How Tight Should a Mini Excavator Track Be After Reinstallation?
Correct track sag measures 1 to 1.5 inches at the midpoint between the front idler and rear sprocket on most mini excavators.
Press down on the top of the track at the midpoint and measure the deflection. Tighter than 1 inch overloads roller bearings and increases fuel consumption. Looser than 1.5 inches allows the track to ride off the sprocket during turns. A mini excavator with correct track tension also delivers more efficient digging — and pairs well with attachments like Mini Excavator Auger systems for post-hole drilling and fence line work.
Once your tracks are seated and tensioned, put that excavator to work. Forge Claw carries professional-grade Mini Excavator Auger attachments built for contractors, landowners, and ag professionals who need reliable drilling performance — with financing available for qualified buyers.